ZZR600 Modifications - Page 3

Grimy · 10-03-2006, 01:16 PM

Quote:

Originally Posted by ZZRrocket

Sounds like fuses my friend. Check your fuses. If you touch the bare wires to metal your going to blow a fuse. That's why all of my connections are covered with 3M shrink wrap. Make sure you plug the Orange wire into the "L" marked on the bottom of the EL12 relay. Also if you have no load equalizer install there is not enough of a load on the electronic flasher relay to allow the signals to flash at the proper rate. Check your fuses.

Solution to the Tridon EL12 Flasher Relay that worked for me. The KURYAKYN # 6004865 load equalizer with the Tridon EL12 Flasher Relay. It has two purple wires and one black wire. On the MOTOTECK undertail LED's all I did was tap into one black wire with the black wire from the load equalizer and tap into each yellow wire with each of the two purple wires. I then plugged the Tridon EL12 flasher relay back into the female connectors that I had installed on the wires. Make sure you plug the Orange wire into the "L" marked on the bottom of the EL12 relay. I used some double sided tape and mount the load equalizer to the rear frame. And presto. I turned the key and turned on my hazard flashers and they flash at a normal rate, just like stock turn signals do. Turn signals right and left also work properly. Problem fixed.

Tridon EL12 Electronic Flasher $8.99 at AutoZone
Kuryakyn Load Equalizer # 6004865 $5.00 at Dealership

We checked the fuse box, is there another place where there are more fuses? All the fuses were unbroken...this is so frustrating!!!

Grimy · 10-04-2006, 12:23 AM

fixed, bad ground!

ZZRrocket · 10-04-2006, 02:29 AM

Quote:

Originally Posted by Grimy

fixed, bad ground!

What wasn't grounded properly?

Grimy · 10-05-2006, 04:02 PM

the resistor

ZZRrocket · 10-05-2006, 05:31 PM

Quote:

Originally Posted by Grimy

the resistor

So do your turn signals flash at the proper rate??

Grimy · 10-05-2006, 07:25 PM

Quote:

Originally Posted by ZZRrocket

So do your turn signals flash at the proper rate??

Yes, everything works well, we tested it out and lol the oxygen tube to the gas tank got pinched when everything was put back together so we had to fix that but the signals work at the proper rate, everything looks great. I put everything on cept the frame sliders. I'll be doing that begining of next week. I would really like a new slip on for the bike bc it would make it much better but....DNV and my bank screwed up and bounced a check so I gotta save some money and pay taxes/registration. I still haven't gotten my seat cover, how long did it take you to get?

ZZRrocket · 10-05-2006, 08:58 PM

"I still haven't gotten my seat cover, how long did it take you to get?"

What seat cover are you talking about?? LUIMOTO or Triboseat??

Grimy · 10-06-2006, 06:17 PM

Quote:

Originally Posted by ZZRrocket

"I still haven't gotten my seat cover, how long did it take you to get?"

What seat cover are you talking about?? LUIMOTO or Triboseat??

i was talking about the triboseat but is there one for the front seat??

ZZRrocket · 10-06-2006, 07:37 PM

Quote:

Originally Posted by Grimy

i was talking about the triboseat but is there one for the front seat??

No the Triboseat cover is for the passenger seat. Are we slipping around on our front seat? Put some duct tape on your ass

WSU_bean · 10-06-2006, 08:23 PM

I am lazy. I don't wanna look where these were previously posted but i am looking to get some cf case covers, a solo cowl, and a sweet tank protector thing like you have zzr. Now tell me where to get them...please. Thanks

ZZRrocket · 10-06-2006, 08:53 PM

The paint matched seat cowl that I have is made by Pyramid and can be purchased from revsperfomance part # 13700 which is black for paint for $180.00. You will have to get the color-rite paint to match your 05 ZZR600. http://www.colorrite.com/product_inf...oducts_id=1045

For those that have a 2006 ZZR600 the Part # 13710e for Galaxy Silver for $230.00 plus shipping.

http://www.revsperformance.com/pyram...seat_cowls.htm

Or you can get a Targa brand seat cowl already painted Metallic Ocean Blue, part # 25-433OB from... http://www.exoticsportbike.com/zx6r_zx6rr_zzr600.htm for $179.99

Cheapest I have found anywhere for Lockhart Phillips Carbon Works Parts
http://www.mawonline.com/lockhart.htm#Carbon%20works

Left
(52444) $77.95 Lockhart Carbon Case Cover Left KAW Mfg.#: 4271097
Right
(52445) $77.95 Lockhart Carbon Case Cover Right KAW Mfg.#: 4271098

Magnetic Tank Protector from MagKnight
http://www.mag-knight.com/

How's that for a 30 minute return time on your request?

Regards,

The Rocket aka the parts Guru

Grimy · 10-06-2006, 09:26 PM

hey jay, i just saw a cbr w/ a front seat cover mesh and looked good thats all....but in all seriousness...do you ever ride around with the "oh shit me" handles on?

ZZRrocket · 10-06-2006, 09:37 PM

Quote:

Originally Posted by Grimy

hey jay, i just saw a cbr w/ a front seat cover mesh and looked good thats all....but in all seriousness...do you ever ride around with the "oh shit me" handles on?

The seat cover that you saw could have been a leather pattern called Basket weave. Corbin has it as an option in leather or vinyl for there seats. Did it look like this sample?

http://corbin.com/materials/

The LUIMOTO seat covers that I have are a Carbon Fiber pattern.

Here are some close up pictures of the Triboseat cover on the passenger seat.

Grimy · 10-06-2006, 09:43 PM

yea, i can do w/o a new front seat cover though...triboseat people lost my order had to re-do it again

ZZRrocket · 10-06-2006, 09:49 PM

Quote:

Originally Posted by Grimy

yea, i can do w/o a new front seat cover though...triboseat people lost my order had to re-do it again

Wow I've never heard anything but good things about the people at Triboseat. There website said to allow 4 weeks for delivery. I received my Triboseat cover in 10 days.