Err 1

[Dieldrin]

When I kill the motor my display reads Err 1. Does anyone know what this means

Thanks

[fz6yamaha]

Fault code: Er-1
Diagnostic Code: --
Symptom: No signals are received from the ECU.
Probable cause of malfunction:
Open or short circuit in wiring sub lead.
Malfunction in meter.
Malfunction in ECU.
____________________

I think I got this from this forum, hope it helps and I am not violating any copywright laws or anything, by the way I will post all the ones I found

[fz6yamaha]

Hope it helps...

Fault Code Definitions for fz6

Here are the Definition of the Fault Codes listed in the FZ6 Service Manual:


Fault Code: 12
Diagnostic Code: --
Symptom: No normal signals are received from the crankshaft position sensor.
Probable cause of malfunction:
Open or short circuit in wiring harness.
Defective crankshaft position sensor.
Malfunction in pickup rotor.
Malfunction in ECU.
Improperly installed sensor.


Fault Code: 13
Diagnostic Code: 03
Symptom: Intake air pressure sensor-open or short circuit detected.
Probable cause of malfunction:
Open or short circuit in wiring sub lead.
Open or short circuit in wiring harness.
Defective intake air pressure sensor.
Malfunction in ECU.


Fault Code: 14
Diagnostic Code: 03
Symptom: Faulty intake air pressure sensor pipe system
Probable cause of malfunction:
detected hose
clogged hose
Intake air pressure sensor hose is detached, clogged,
kinked, or pinched.
Malfunction in ECU.


Fault Code: 15
Diagnostic Code: 01
Symptom: Throttle position sensor-open or short circuit detected.
Probable cause of malfunction:
Open or short circuit in wiring sub lead.
Open or short circuit in wiring harness.
Defective throttle position sensor.
Malfunction in ECU.
Improperly installed throttle position sensor.


Fault Code: 16
Diagnostic Code: 01
Symptom: A stuck throttle position sensor is detected.
Probable cause of malfunction:
Stuck throttle position sensor.
Malfunction in ECU. 01


Fault Code: 19
Diagnostic Code: 20
Symptom: Open circuit in the input line of ECU No4 terminal is detected when the start switch is pressed.
Probable cause of malfunction:
Open circuit in wiring harness (ECU coupler).
Malfunction in ECU.


Fault Code: 21
Diagnostic Code: 06
Symptom: Coolant temperature sensor-open or short circuit detected.
Probable cause of malfunction:
Open or short circuit in wiring harness.
Defective coolant temperature sensor.
Malfunction in ECU.
Improperly installed sensor.


Fault Code: 22
Diagnostic Code: 05
Symptom: Intake air temperature sensor-open or short circuit detected.
Probable cause of malfunction:
Open or short circuit in wiring harness.
Defective intake temperature sensor.
Malfunction in ECU.
Improperly installed sensor.


Fault Code: 30
Diagnostic Code: 08
Symptom: The motorcycle has overturned.
Probable cause of malfunction:
Overturned.
Malfunction in ECU.


Fault Code: 33
Diagnostic Code: 30
Symptom: Open circuit is detected in the primary lead of the ignition coil (# 1, #4).
Probable cause of malfunction:
Open circuit in wiring harness.
Malfunction in ignition coil.
Malfunction in ECU.
Malfunction in a component of ignition cut-off circuit system.


Fault Code: 34
Diagnostic Code: 31
Symptom: Open circuit is detected in the primary lead of the ignition coil (# 2, #3).
Probable cause of malfunction:
Open circuit in wiring harness.
Malfunction in ignition coil.
Malfunction in ECU.
Malfunction in a component of ignition cut-off circuit system.


Fault Code: 41
Diagnostic Code: 08
Symptom: Lean angle cut-off switch-open or short circuit detected.
Probable cause of malfunction:
Open or short circuit in wiring harness.
Defective lean angle cut-off switch.
Malfunction in ECU.

Fault Code: 42
Diagnostic Code: 07, 21
Symptom: No normal signals are received from the speed sensor; or, an open or
short circuit is detected in the neutral switch.
Probable cause of malfunction:
Open or short circuit in wiring harness.
Defective speed sensor.
Malfunction in vehicle speed sensor detected unit.
Defective neutral switch.
Malfunction in the engine side of the neutral switch.
Malfunction in ECU.


Fault Code: 43
Diagnostic Code: 09
Symptom: Supply power to the injector and fuel pump is not normal
Probable cause of malfunction:
Open circuit in wiring harness. (red/blue line or blue/yellow line)
Malfunction in ECU.


Fault Code: 44
Diagnostic Code: 60
Symptom: An error is detected while reading or writing on EEPROM.
Probable cause of malfunction:
Malfunction in ECU. (The CO adjustment value is not properly written on or read from the internal memory).


Fault Code: 46
Diagnostic Code: --
Symptom: Power supply to the FI system is not normal.
Probable cause of malfunction:
Malfunction in "CHARGING SYSTEM".


Fault code: 50
Diagnostic Code: --
Symptom: Faulty ECU memory. When this malfunction is detected, the code
number might not appear on the meter.
Probable cause of malfunction:
Malfunction in ECU. (The program and data are not
properly written on or read from the internal memory.)


Fault code: Er-1
Diagnostic Code: --
Symptom: No signals are received from the ECU.
Probable cause of malfunction:
Open or short circuit in wiring sub lead.
Malfunction in meter.
Malfunction in ECU.


Fault code: Er-2
Diagnostic Code: --
Symptom: No signals are received from the ECU within the specified duration.
Probable cause of malfunction:
Improper connection in wiring sub lead.
Malfunction in meter.
Malfunction in ECU.


Fault code: Er-3
Diagnostic Code: --
Symptom: Data from the ECU cannot be received correctly.
Probable cause of malfunction:
Improper connection in wiring sub lead.
Malfunction in meter.
Malfunction in ECU.


Fault code: Er-4
Diagnostic Code: --
Symptom: Non-registered data has been received from the meter.
Probable cause of malfunction:
Improper connection in wiring sub lead.
Malfunction in meter.
Malfunction in ECU.
·
__________________

[CorvetteBoy]

That fault code means there is a problem with signals to the ECU. It may be as simple as a loose connection (check couplers in the harness) or it could be a short or even a malfunctioning ECU.

Carnac the Magnificent I'm not, but I do see a trip to the dealer in your future.

[CorvetteBoy]

fz6 yamaha was all over that question like a fat kid on a snickers bar.

[fz6yamaha]

jajja , CorvetteBoy is right I was happy I saved that info sometime and was useful to somebody.

[Hippie]

I have been getting the same every once in a while...
Do you have a Powercommander hooked up?

People here told me not to worry until it appears while riding, and not when shutting off the ignition...

My gut feeling is it is a precursor to the TPS syndrome...

[segue00]

ER-1

There is a thread about that same exact error a while back, but I can't find it.

I wouldn't worry about it if it happens at shut-downs since the display goes off after the ECU.

Worry about it when it happens at start-ups when the ECU goes on before the display.

[Hippie]

Yup.
I started that thread...

[fizzygrrl]

Crap, my new bike worked last night and now it's got an error code 12 on it. I guess I get a crash course is "WTF is wrong with my bike and I better fix it now"

[Hippie]

Originally Posted by fizzygrrl

Crap, my new bike worked last night and now it's got an error code 12 on it. I guess I get a crash course is "WTF is wrong with my bike and I better fix it now"

Fault Code: 12
Diagnostic Code: --
Symptom: No normal signals are received from the crankshaft position sensor.
Probable cause of malfunction:
Open or short circuit in wiring harness.
Defective crankshaft position sensor.
Malfunction in pickup rotor.
Malfunction in ECU.
Improperly installed sensor.

[Hippie]

Hey Mod / Fred

If it is not already..
Maybe we can Sticky that Error code list FZ6Yamaha posted up earlier in this thread.